Chapter 4: [CE] Commercial Energy Efficiency, 2018

Assembly descriptions can be found in ANSI/ASHRAE/IESNA Appendix A. Where using R-value compliance method, a thermal spacer block shall be provided, otherwise use the U-factor compliance method in Table C402.1.4.; R-5.7ci is allowed to be substituted with concrete block walls complying with ASTM C90, ungrouted or partially grouted at 32 inches or less on center vertically and 48 inches or less

Learn More

downloads.cs.stanford.edu

UNK the, . of and in " a to was is ) ( for as on by he with 's that at from his it an were are which this also be has or : had first one their its new after but who not they have ; her she ' two been other when there all % during into school time may years more most only over city some world would where later up such used many can state about national out known university united then made

Learn More

2017 FBC, ENERGY CONSERVATION - CHAPTER 4

ICC Digital Codes is the largest provider of model codes, custom codes and standards used worldwide to construct safe, sustainable, affordable and resilient structures.

Learn More

Chapter 4: [CE] Commercial Energy Efficiency, 2015

Equipment not designed for operation at AHRI Standard 550/590 test conditions of 44°F (7°C) leaving chilled-water temperature and 2.4 gpm/ton evaporator fluid flow and 85°F (29°C) entering condenser water temperature with 3 gpm/ton (0.054 I/s • kW) condenser water flow shall have maximum full-load kW/ton (FL) and part-load ratings

Learn More

Chapter 4: [CE] Commercial Energy Efficiency, 2017 FBC

Assembly descriptions can be found in ANSI/ASHRAE/IESNA Appendix A. Where using R-value compliance method, a thermal spacer block shall be provided, otherwise use the U-factor compliance method in Table C402.1.4.; R-5.7ci is allowed to be substituted with concrete block walls complying with ASTM C90, ungrouted or partially grouted at 32 inches or less on center vertically and 48 inches or less

Learn More

2018 INTERNATIONAL ENERGY CONSERVATION CODE (IECC) -

a. Assembly descriptions can be found in ANSI/ASHRAE/IESNA Appendix A. b. Where using R-value compliance method, a thermal spacer block shall be provided, otherwise use the U-factor compliance method in Table C402.1.4.. c. R-5.7ci is allowed to be substituted with concrete block walls complying with ASTM C90, ungrouted or partially grouted at 32 inches or less on center vertically and 48

Learn More

Chapter 4: [CE] Commercial Energy Efficiency, Energy

Equipment not designed for operation at AHRI Standard 550/590 test conditions of 44°F (7°C) leaving chilled-water temperature and 2.4 gpm/ton evaporator fluid flow and 85°F (29°C) entering condenser water temperature with 3 gpm/ton (0.054 I/s • kW) condenser water flow shall have maximum full-load kW/ton (FL) and part-load ratings

Learn More

LiveInternet @ Статистика и дневники, почта и поиск

We would like to show you a description here but the site wont allow us.

Learn More

(PDF) Mechanical & Electrical Equipment for Buildings

Mechanical & Electrical Equipment for Buildings, 11th edition, John Willey. Lukman Hakim. Download PDF

Learn More

2020 FLORIDA BUILDING CODE, ENERGY CONSERVATION, 7TH

Warm air furnaces, gas-fired Non-weatherized < 225,000 Btu/h 80% AFUE or 80% E t c 81% AFUE: DOE 10 CFR, Part 430 or Section 2.39, Thermal Efficiency of ANSI Z 21.47: Weatherized gas furnace: Maximum capacity c: 80% E t f: Section 2.39, Thermal Efficiency of ANSI Z21.47: Warm air furnaces, oil-fired Non-weatherized < 225,000 Btu/h 83%

Learn More